复合固体推进剂中固体填料的安息角测试与仿真

复合固体推进剂含有固体颗粒较多，离散单元法是一种适合固体推进剂生产过程数值仿真的有效方法，颗粒物料的接触参数是保证离散单元法仿真精度的关键。本文以复合固体推进剂的主要组分铝粉和高氯酸铵固体颗粒为研究对象，通过实验测试获得了相关物料的安息角，利用专业离散元软件EDEM仿真模拟了安息角测试实验过程，建立了物料安息角与接触参数之间的联系。研究表明，滚动摩擦系数和滑动摩擦系数越大，安息角越大，物料流动性越差。对比仿真与实验结果，通过逆向反推法确定了物料的滑动摩擦系数和滚动摩擦系数两个关键接触参数。铝粉与高氯酸铵1∶2混合颗粒的滑动摩擦系数为0.2，滚动摩擦系数为0.05。为固体推进剂加工生产过程离散元数值仿真提供了关键基础数据。     

Multicellular Tumor Spheroids (MCTS) as a 3D In Vitro Evaluation Tool of Nanoparticles

Multicellular tumor spheroid models (MCTS) are often coined as 3D in vitro models that can mimic the microenvironment of tissues. MCTS have gained increasing interest in the nano‐biotechnology field as they can provide easily accessible information on the performance of nanoparticles without using animal models. Considering that many countries have put restrictions on animals testing, which will only tighten in the future as seen by the recent developments in the Netherlands, 3D models will become an even more valuable tool. Here, an overview on MCTS is provided, focusing on their use in cancer research as most nanoparticles are tested in MCTS for treatment of primary tumors. Thereafter, various types of nanoparticles—from self‐assembled block copolymers to inorganic nanoparticles, are discussed. A range of physicochemical parameters including the size, shape, surface chemistry, ligands attachment, stability, and stiffness are found to influence nanoparticles in MCTS. Some of these studies are complemented by animal studies confirming that lessons from MCTS can in part predict the behaviour in vivo. In summary, MCTS are suitable models to gain additional information on nanoparticles. While not being able to replace in vivo studies, they can bridge the gap between traditional 2D in vitro studies and in vivo models.     

Investigation of functional core-rim composite part production by inserted powder injection moulding

In this study, the use of Cu and Ni interlayers have been investigated for functional core-rim composite part production with WC-Co 9?wt-% feedstock/steel. For this purpose, different experiments have been performed and joining condition, shear strength and microstructure of the intermediate region have been examined. It has been found that AISI 4340 insert/WC-Co have been joined and 85.8?MPa shear strength achieved, but high speed steel insert has not joined. Moreover, it has been determined that better results are obtained with Ni interlayer. Under the same conditions, when the 40?µm Ni interlayer has been used between AISI 4340 core and WC-Co rim, shear strength has been increased approximately twice and has been 162.7?MPa.     

脱硫胶粉在乳化改性沥青中的应用

考察了不同规格胶粉及不同脱硫程度的脱硫胶粉对橡胶改性乳化沥青性能的影响,结果表明,采用100目胶粉即可制备出橡胶改性乳化沥青,但乳化沥青的性能较差;采用活化度为50%左右的100目脱硫胶粉制备乳化沥青时,脱硫胶粉的用量相比于胶粉可大幅提高;在通过外掺100目50%左右活化度的脱硫胶粉(质量分数15%,以沥青计,下同)和质量分数2%的苯乙烯-丁二烯-苯乙烯嵌段共聚物改性的乳化沥青中添加质量分数1%的丁苯胶乳,所制备橡胶改性乳化沥青无筛上剩余物,5 d储存稳定性为2.9%,蒸发残留物的25℃针入度、软化点和5℃延度分别为55 (0.1 mm)、64.5℃和22.5 cm,能够满足乳化改性沥青的技术指标要求。     

涡流空气分级机熵产与分级性能分析

利用热力学第二定律中的熵产理论对涡流空气分级机各不可逆因素引起的熵产进行分析，通过粉料分级试验对其分级性能进行验证，获得了黏性熵产、湍流熵产和壁面熵产分布特点及操作参数对熵产和分级精度的影响规律。熵产分析结果表明，涡流空气分级机内湍流熵产和壁面熵产占总熵产的比例高达56.41%和43.11%，湍流熵产主要产生于转笼叶片间和转笼内部，进风口和细粉出口壁面剪切引起较大壁面熵产；此外，转笼转速和进口风速变化分别仅对转笼区域和切向进风口区域内气流运动熵产影响较大，进口风速-转笼转速处于8.6m/s、 800r/min和18m/s、1200r/min操作工况附近时，涡流空气分级机内总熵产/总能变化率较小，分级流场稳定性较高，对粗、细颗粒分离有利，该工况下分级机的粉料分级试验效果较好，说明熵产理论可用于涡流分级机内流动分析及其操作参数的优化匹配。     

MAPP/EAA处理对聚丙烯/小麦秸秆粉复合材料性能的影响

研究了马来酸酐接枝聚丙烯（MAPP）、乙烯丙烯酸共聚物（EAA）处理对聚丙烯（PP） /小麦秸秆粉（WSP）复合材料性能的影响。结果表明，随着体系中MAPP质量份数的增加，PP/WSP的拉伸强度和弯曲强度均逐渐增大，但冲击强度却先增加后减小，复合材料达到塑化峰的时间逐渐延长；使用EAA后，无论体系中是否已经使用了MAPP，PP/WSP的拉伸、弯曲和冲击强度均可得以提高，特别对于未使用MAPP的体系，效果更加明显，可分别提高65.04 %、45.42 %和6.75 %，储能模量增加，表面疏水性增强，平衡扭矩从13.9 N·m降至11.8 N·m，吸水尺寸变化率及吸水率下降，吸水平衡时间缩短；使用EAA可改善PP/WSP中WSP与PP间的界面结合，改善PP/WSP力学性能、热稳定性能、表面疏水性能、尺寸稳定性能和加工性能，降低其吸水率。     

新型活化环氧富锌涂层的耐腐蚀性研究

富锌涂料在防腐蚀领域具有广泛应用，然而其长效防护性能却受到锌粉活性影响。本文以冷涂锌涂层、传统环氧富锌涂层作为对照，研究了新型具有电化学活性的环氧富锌涂层在盐雾加速腐蚀试验后的耐腐蚀性。宏观形貌分析表明：盐雾加速腐蚀 1 800 h后，活化环氧富锌涂层表面并未出现锈点；采用扫描电子显微镜、维体式显微镜观察试验后涂层的表面形貌和涂层结构，发现活化环氧富锌涂层微观表面更加平滑，锌粉并未出现大面积的氧化，涂层内部大小锌粉颗粒均匀排列；通过电化学方法研究涂层的耐蚀机理与防护性，发现活化富锌涂层具有更持久的低防护电位。以上研究结果表明，较冷涂锌及传统环氧富锌涂层而言，新型活化环氧富锌涂层具有优异的长期防护性能，是值得关注和研究的一种新型技术。     

可逆感温变色聚丙烯专用料的制备及性能

通过两步法制备可逆感温变色聚丙烯（PP）专用料，首先将乙烯-辛烯共聚物（POE）与可逆感温变色粉于微型双螺杆挤出机中挤出造粒制备色母料，然后将PP与色母料熔融共混挤出制备可逆感温变色PP专用料。探讨了色母料含量对PP专用料感温变色性能、力学性能、热学性能及微观形貌的影响。结果表明，利用POE与PP良好的相容性，实现了可逆感温变色粉在PP基体中均匀的分散，可逆感温变色PP专用料表现出优异的可逆感温变色性能和冲击性能。     

新型着色材料——速溶色浆粉的测试与应用

介绍了通过初级颜料的润湿、研磨与分散、稳定处理技术,使助剂和树脂均匀地包裹在颜料表面,并通过特殊工艺制得水性和油性色浆粉,并赋予了很好的速溶性和分散性。